The Science of Comfort

Your Premiere Source For All Things HVAC

What is Inlet Effect?

Posted by Price Industries on August 27, 2019 at 9:57 AM
Price Industries

Inlet Effects 

Controls_Office_Graphic_VARITHERM+PRC_v137comp
ASHRAE Standard 70 guidelines are in place so that ideal conditions are present during GRD testing
and to ensure the testing is repeatable. It is important to note that the performance
published in the Price catalog is based on these ideal conditions outlined in ASHRAE 70 and that
any field modifications can affect the performance of the outlet. There are five common field conditions and their influence on the air pattern of a given diffuser:
Let's compare air patterns for ASHRAE Standard 70 compliant tests against those with the
five field inlet conditions listed above.
 
Three different types of ceiling diffusers will be used to depict the results:
  • Perforated diffuser
  • Directional diffuser
  • Radial diffuser

To illustrate the air pattern, constant velocity plots (isovels) that display an envelope of air at an equal velocity will be used. Note that the diffuser shown in each image is a generic image intended to represent the diffuser described in the text. 

All diagrams will show the isolated velocity at 100 fpm for easy comparison. Each test was run at the same airflow, and the dampers were installed with three (3) equivalent duct diameters and adjusted to obtain a pressure drop of 0.25 inches w.g.
 
 

ASHRAE 70 Standard Installation Using Three Straight Duct Diameters 

In Figures 2 to 4, lines of equal velocity (isovels) are shown for the three types of diffusers when installed using the ideal inlet conditions described in ASHRAE 70 installation guidelines, as shown in Figure 1.
Diffuser with 3 equivalent diameters of straight duct at inlet
 
Figure 1: ASHRAE Standard 70 requires three duct diameters
 
Figure 2 depicts a typical pattern for a perforated diffuser, such as the Price PDS. This diffuser produces four distinct air jets, originating from the corners of the diffuser face. 
 

Blog_Assets_01_v002

Figure 2: Perforated Diffuser

Figure 3 displays the pattern delivered from a directional diffuser, like the Price SMD diffuser. This diffuser also displays four distinct air jets however, the airstreams root from the sides of the diffuser face instead of the corners, as was seen with the perforated diffuser. 

Blog_Assets_02_v002

Figure 3: Directional Diffuser 

Figure 4 shows the air pattern from a radial patterned diffuser like the Price square plaque diffuser, model SPD. Unlike the first two diffusers, this product has a radial pattern encompassing a full 360 degrees surrounding the diffuser. As a result, the throw distances will be slightly shorter at the same airflows when compared to a four-way diffuser like the PDS or SMD.

Blog_Assets_03_v002

Figure 4: Square Plaque Diffuser

 

90 Degree Hard Elbow        

The first field installed inlet condition that will be discussed is a 90 degree hard duct elbow, the installation of which is shown in Figure 5. The diagrams below display two different isovels superimposed on top of each other.

SPD_HardElbow_v001

 
Figure 5: Hard Ducted Elbow Installation

The blue isovel represents ideal inlet conditions and will be included for comparison against all field installations. The purple isovel illustrates how the 90 degree hard elbow on the diffuser inlet affects the air pattern for the three different diffusers. The air pattern of the perforated diffuser is not significantly affected, as it still displays a distinct four-way throw shown in Figure 6. However it is clear that the 90 degree elbow has shifted the pattern slightly clockwise.

Smoke2_A
 
Figure 6: Perforated Diffuser
 
Figure 7, depicting the directional diffuser, indicates that the pattern placement remains unchanged with the 90 degree elbow. However, there is a drastic reduction in the throw on three sides and an increase on one. Since the same amount of air is being delivered through the diffuser, it is also possible that the reduction in throw in three directions has resulted in an increased drop, possibly causing discomfort to the occupants.
 
Smoke2_B
 
Figure 7: Directional Diffuser
 
The plaque diffuser shows more resilience, as the pattern is only slightly changed as seen in Figure 8. This slight modification would likely not produce a noticeable difference to the occupants. 
Smoke2_C
 
Figure 8: Square Plaque Diffuser
 
 

90-Degree Flexible Duct Connection

In comparison to the 90 degree hard elbow, a 90 degree flexible duct elbow changes the air pattern
more significantly. Figure 9 shows a typical flexible duct connection.
SPD_FlexDuct_v001
 
Figure 9: 90-Degree Flexible Duct Connection
 
The yellow isovel displays the adjusted air pattern when connected to a 90 degree flex duct. This added affect is primarily due to an increased surface roughness due to the spiral of the flex duct as well as an uneven airflow caused by the non-fixed radius.
 
The perforated diffuser, as shown in Figure 10, is now distributing a three-way throw pattern instead of the intended four-way pattern. This could cause stagnant zones adjacent to the side of the diffuser that is no longer discharging fresh supply air.
 
Smoke3_A
 
Figure 10: Perforated Diffuser
 
The pattern for the directional diffuser in figure 11 has also been compromised. There is a reduction in throw on all four sides, with a drastic reduction on two of the sides. This reduction in throw will also lead to an increased drop into the occupied zone and likely cause discomfort to the occupants. 
 
Smoke3_B
 
Figure 11: Directional Diffuser
 
Similar to the 90 degree hard duct, the square plaque diffuser’s pattern has not been affected significantly, as shown in figure 12, although there is a noticeable shift in the distribution area.
 
Smoke3_C
 
Figure 12: Square Plaque Diffuser
 
 
 

Radial Opposed Blade Damper

Adding a radial opposed blade damper to a diffuser neck, pictured in Figure 13, to the neck of the
diffuser will not only increase pressure drop, but affect the air pattern as well.
Radial Opposed Blade Damper VCR7
Figure 13: Radial Opposed Blade Damper
 
The light blue isovel represents the changes to the air pattern after installing a radial opposed blade
damper. The damper has significantly changed the pattern of the perforated diffuser as seen in Figure
14.
 Smoke4_A

 

Figure 14: Perforated Diffuser
 
The pattern has morphed into an almost radial pattern, with no distinct air jets. Some directional
diffusers are positioned such that air jets from one diffuser will intersect with air jets from a different
diffuser. This will cause the air to deflect downwards, towards the occupied zone, helping to properly
mix the space. In this case, the change in air pattern could mean that this junction would not occur
creating discomfort to the occupants as the conditioned air would remain above the occupied zone.
 
The directional diffuser in Figure 15 retained its four-way pattern, however, with a shortened throw and a probable increase in drop. 
 
Smoke4_B
 
Figure 15: Directional Diffuser
 
Once again, the square plaque diffuser remains relatively unchanged, with the pattern only slightly affected by the addition of the damper (Figure 16). The radial opposed blade damper, due to its design, retains a fairly even air distribution across the entire area of the inlet.
 
Smoke4_C
 
Figure 16: Square Plaque Diffuser
 

Butterfly Damper

The green isovels in the following three figures represent the air patterns produced by the diffusers
with a butterfly damper (Figure 17) installed.
 
Butterfly Damper
Figure 17: Butterfly Damper
 
 
Figure 18 indicates adding a butterfly damper does not affect the pattern of the perforated diffuser, but will nonetheless shift the pattern in a counter clockwise direction. 
 
Smoke5_A
 
Figure 18: Perforated Diffuser
 
The pattern of the directional diffuser is also left unmarred, but as seen in Figure 19, the throw is reduced in all four directions. As in the previous cases, a reduction in throw will, in all likelihood cause an increase in drop which can decrease occupant comfort levels. 
 
Smoke5_B
 
Figure 19: Directional Diffuser
 
The square plaque diffuser experiences a decreased throw as well, potentially resulting in an increased drop, and therefore decreased occupant comfort, depicted in Figure 20.
 
Smoke5_C
 
Figure 20: Square Plaque Diffuser
 
 

Radial Damper

 
Radial dampers, as shown in Figure 21, operate by limiting the flow through the duct with
bowtie shaped plates. A major disadvantage to using this style of damper is a drastic increase in
pressure drop due to the uneven reduction in cross section of the inlet area.
 
Bowtie Damper
Figure 21: Radial Damper
 
The radial damper isovels are displayed in a purple color. Of the 5 inlet conditions presented,
Figure 22 depicts the most profound modification seen to a diffuser throw pattern. The radial damper
has altered the pattern from four distinct jets to a, six-way star like pattern.
 
Smoke6_A
 
Figure 22: Perforated Diffuser
 

The diffuser retains its four-way pattern, but the addition of the radial damper shortens the throw and consequently increases the drop. Compared to the four previously discussed inlet conditions, the radial damper causes the most dramatic effect on air pattern of the square plaque diffuser, although still much less than with the other diffusers. Similar to earlier examples, the directional diffuser shown in Figure 23 sees a less drastic change in air pattern. 

 
Smoke6_B
 
Figure 23: Directional Diffuser
 
The normally radial pattern of the plaque diffuser (Figure 24) is transformed into a more oblong shape, increasing throw in some directions, and reducing throw in others.
 
Smoke6_C
 
Figure 24: Square Plaque Diffuser
 

Conclusion

This study has revealed the different degrees to which ceiling diffusers are affected by an assortment of common field inlet conditions.
 
Depending on the type of diffuser selected, different inlet conditions can have a varying impact on the performance of a diffuser ranging from minor to significantly detrimental. This demonstrates that proper diffuser selection and consideration of field inlet conditions is important. Certain diffusers have more yielding design qualifications, and should be used in instances where less than ideal inlet conditions exist.
 
Primarily, the square plaque diffuser experienced minor changes to its overall pattern and throw when tested with the five inlet conditions. Conversely, it was shown that the perforated diffuser was the most affected by varying inlet conditions.
 
By choosing the square plaque diffuser in areas where these inlet conditions are expected and
unavoidable, the risk of potential discomfort for the occupants can be reduced.
 
For more information on this and other topics, please see the Price Engineer’s HVAC Handbook or email grd@priceindustries.com with specific GRD questions.
 
New call-to-action
 

Topics: GRD, Diffusers, ASHRAE 70, Inlet Effect, Grilles

At Price, when we say “the sky is the limit,” we actually mean it.

Our customers have come to count on a consistent and ever-increasing stream of new products and enhancements.  Price has a large team of experienced and talented engineers who are consistently working on breakthrough ideas.  We are not afraid to move into whole new product categories if we believe we have a contribution to make.

  • Research & Innovation
  • Technical Tours
  • Training Classes
  • Targeted Discussions
  • Mock-up Testing
  • Custom Solutions & Specials
  • Custom Finishes
  • Computational Fluid Dynamics
  • Virtual Reality

Subscribe to Email Updates

Recent Posts